QTY.

ITEM DESCRIPTION

OPENING

1

Bianco Opener/Detwister with Squeeze Set accumulator, ceiling mounted Detwister,

Beater/opening bar, Scroll Roll opening 101" face, Pivot Guiding 95" face, Plaiter and pull roll exit.

DYEING

1

Zimmer/Gaston County Altered Pressure Jig Dyer, 144" x 12" Drums, 58" to 62" max. diameter fabric load, includes (2) add tanks 30.5" dia. X 22" deep with Lighnin Mixers, heat exchanger, lint filter, 5-HP liquor pump 3x2, 11-Kw Vertical Gearmotor Drives on each Drum, NO CONTROLS.

Alt. Gaston County 2000 N.B.# 27723, S/N F82150A-701-1

Alt. Gaston County 2003 N.B.# 3115, S/N F82393A

Orig. Zimmer Tag: JM58-134-ELHT.SAL.R, S/N 51.01.11.01.J-447

1

Zimmer/Gaston County Altered Pressure Jig Dyer, 144" x 12" Drums, 58" to 62" max. diameter fabric load, includes (2) add tanks 36" dia. X 31" deep with Lightnin Mixers, heat exchanger, lint filter, 5-HP liquor pump 3x2, 11-Kw Vertical Gearmotor Drives on each Drum, Zimmer Controller with Beckoff Touch Screen

Alt. Gaston County 2002 N.B.# 27903, S/N D20129

Orig. Zimmer Tag: JM58-134-ELHT.SAL.R, S/N 53.01.01.03-J-579

1

Kemco Hot Water Recovery System, with Double-Pass Heat Exchangers, each 31'8" long, wiht 10,000 gallon stainess steel hot water tank 10' dia. x 18' tall, two 20 HP pumps.

Color and Chemical Kitchen, consisting of:

BLEACHING (Bleach range components remaining):

1

a. Roll Table 108" wide x 120" long

b. Non-driven Cradle let-off, 4-roll, 140" x 8.75" Bed Rolls

c. Pipe-type J-Scray 144" wide with slotted pull roll

d. Webtech Double-Scroll Opening Rolls with 3-roll Pivot Guider 154" face width, Model W5G-Z/3400HD, S/N 22, 2004

e. Kalin Lint Vacuuming System, 138" width on carrier rolls, (2) Suction Fans with collection bags on each side on stands.

f. Menzel Singer 144SI, S/N 01109, Yr. 1988, 6-Burners, Water-cooled Carrier Rolls, Combustion Blower, Exhaust Blower and Hood.

g. Quench/Chemical Tank, 140" face x 68" fr/bk x 44" deep with 6-bottom immersion rolls and 5-top rolls.

h. Kusters Horizontal Nip Set type 225.80, 1992, #M17177-01, 138" face width Rubber/Stainless rolls, compensator. 10-HP vertical gearmotor drive.

i. Kusters Roller Bed Steamer, 138" face width, approx. 2500 yard capacity, Tight-Strand Entry section with 7/6 Rolls, Roller-Bed section 268" long.

j. Webtech Opening/Guiding System, 154" Double Scroll opening and 154" Pivot Guider

k. Single dip Wet-out box, 138" face rolls, 2-top and 1-immersion roll.  19" fr/bk x 28" deep.

l. Vacuum System with Nash SC-7 Pump, 50-HP motor, separation tank and silencer, 138" vacuum slot.

m. Double dip Wet-out box, 138" face rolls, 2-top and 2-immersion rolls.  34" fr/bk x 28" deep.

n. 1998 KTM Nip Set, 138" face width Rubber/Stainless rolls, 10-HP DC motor drive, S/N F980069-01

o.  Morrison Horizontal Washer, 138" face, 7 x 7 rolls.

p.  Morrison Nip Set, 138" face width Rubber/Stainless rolls, 10-HP DC motor drive,

q. Morrison Horizontal Washer, 138" face, 7 x7 rolls.

(break in line)

r. (30) Dry Cans, 3-Stacks of 10-Cans each, 134" face width, first stack Teflon coated, balance SS, 75-PSI Pressure Rating,, 7.5-HP DC motor drive on each stack.

Note: think made by Greenville Machinery, 4-bolt journal heads

s. (2) Cooling Cans 134" face - overhead mounted

t. Pipe-type J-Scray 144" wide with slotted pull roll

u. Webtech Opening/Guiding System, 154" Double Scroll opening and 154" Pivot Guider

v. Diversified Textile Systems A-Frame Winder, 142" face width, Lay-on Roll/Surface driven, 7.5-HP 480 volts.

w.  Note: Main Drive and Controls not available with components.

Set Spare Nip Set Rolls

a. Rubber roll 138" face x 18" dia. with bearings mounted

b. Steel roll 138" face x 18" dia. with bearings mounted

FINISHING

1

Marshall & Williams Tenter Range #4

a. Roll Table 38" x 97" wide

b. Non-driven Cradle Let-off, 126" face

c. Small SS J-Scray with pull roll, 80" high x 47" fr/bk, with Sky-in stand, E&L KF-20 Guiders on bridge.

d. Kusters Finishing Padder (no tag) 140" face Rubber/Stainless Steel rolls, 130.5" x 18" dia., liquor trough with lift, 15-HP motora and gearbox.

e. 3-Roll Compensator

f. Vacuum System with Sutorbilt Pump and 50-HP motor, separator, silencer and 130" SS slot.

g. Aztec Predryer, 2-pass 8-burners, gas fired, NYC combustion blower.

h. (10) Can Stack, Morrison 120" face width, 126-PSI Pressure, Rating, 7.5-HP DC drive motor.

i. Greenville Steel 3-Roll Compensator

j. 2002 Webtech Weft Straightener PS208HD, S/N 023, 130" Bow Rolls, 6-sensor heads, 220/1 volts.

k. Marshall & Williams Clip Tenter Frame, including operator platform and contrrols, 132" feed roll, Webtech Edge Sensors and Rail Guiding System, 13' Swing Rail entry, 6-Zone low profile gas fired house with (6) Maxon 415P OvenPak Burners and (12) 15-HP circulation fans, 12' exit zone with stripper rolls, Auto-chain lubrication system, 30-HP DC main drive motor.

l. Menzel 3-Roll Compensator, 134" face

m. Pipe-type J-Scray with driven pull roll, Inspection Board with overhead lighting and operator platform.

n. M&W 3-Roll Compensator

o. Sky-stand on exit with E&L KF-2020 Guiders on bridge, 120" face width, with Hardened Roll and Anvil mount for score slitter heads, Steadweb Tension Controls.

p. Krantz 701M Automatic Batcher S/N 8066, 154" face Bed Rolls, Swing-Shear Cut-off.

q. Main Drive, Controls, Motors, etc.

1

Marshall & Williams Tenter Range #2

a. Roll Table & Cradle, 130" wide (small dia. Rolls)

b. SS Scray with driven pull roll, KF-2020Guiders on bridge

c. Operator platform

d. Radiation Systems PreDryer, Single Pass - with RSI Thermonitor

e. Kusters Vertical Padder, Rubber/Stainless Rolls 130.5" face,

f. Nash SC-7 Vacuum System with 50-HP motor, trap and silencer, 130" slot

g. Radiations Systems PreDryer, Single Pass - with RSI Thermonitor

h. Mahlo RFMC-94H Weft Straightener 146" wide, 480 volts

i. Marshall & Williams Clip Tenter Frame 2985G, MSO 4459D, 150" max. opening, with operator platform, op. controls, 10' Swing Rail entry with rail guiding, M&W 8-zone low profile gas fired house with (8) Maxon 415P OvenPak Burners and (16) 15-hp circulation fans, 10' Exit Rail section with stripper rolls.

j. Mahlo Sensor

k. 3-Roll Tension Set

l. Menzel 3-Roll Compensator 134CP, #10107, 1988

m. Menzel Pipe-type scray with slotted pull roll

n. Sky-stand with Toyo air Guiders on bridge

o. M&W Compensator/Accumulator 140" face, 4-rolls up and 3-rolls down, with lighted Viewing board

p. Kranrtz Automatic Batcher 701M, S/N 8278, 154" face on Bed rolls, Shear-Cut doffing, and A-Frame Lay-on roll.

q. Main Drive, Controls, motors, etc.

1

Wash Range, consisting of;

a. Pipe-typ J-Scray with driven pull roll and Guider Specialty Air Guiders 18"

b. (3) Kusters Horizontal Washers, 120" face width, Type 225.74-172, 1985, M7977-106/108-110, and (3) Kusters Nip Sets 120" face Rubber/Stainless with 7.5-HP DC motors

c. Nash Vacuum System with 30-HP motor, trap and silencer, and 120" slot.

d. (16) Morrison Dry Can, 2-stacks of 8 cans each, 120" face width, 125-PSI Pressure Rating, 7.5-HP DC motor and belt drive.

e. Driven Pull Roll and fabric slide to carrier roll

f. Cooper A-Frame Winder 132" face width with Lay-On Roll

g. Drive, Controls, motors, etc.

1

Sanforizing Range, consisting of;

a. Stainless J-Scray with 7.5-HP driven pull roll

b. Sky-In Stand with Guider Specialty Air Guiders on bridge

c. Timing Can (overhead mount)

d. Morrison Cole Spray House

e. 2001 Morrison Compressive Shrinking Machine T-262, 135" face width on Cylinder with 132.5" Rubber Belt (3" thick), 25-HP Drive motor

f. Morrison Palmer T-262, with 130" face width 84" dia. Cylinder with 126" Felt Blanket

g. 3-Cooling Cans (overhead mount)

h. Menzel A-Frame Winder 130SBE, #01227, 2001, 10-HP Electric Drive on Lay-on roll.

i. Main Drive, Controls, motors, etc.

1

Calendering Range, consisting of;

a. Fed by idling A-Frame (no drive)

b. Operator Platform

c. John Verduin 2-Roll Calender, S/N 672-B-3361, 132" face width, 130-Tons Hydraulic Pressure, C-Face arrangement for quick roll change, Top Roll is 132" x 20" dia. Chromed-Steel with gas burner, Bottom Roll is 132" x 18" dia.  Swimming Roll with Nylon Sleeve hydraulically expanding.  Includes 20-HP 240 volt DC drive, 10-Ton Crane for removing Rolls from machine, combustion blower, oil cooler.

d. A-Frame Winder with Center Drive and Lay-On Roll

1

Transfer Printing Range, consisting of;

a. Jack Stand and Stainless J-Scray with edge sensors

b. Operator Platform

c. Singer(?) Transfer Machine with 36" dia. X 149" face width Hot-Oil Cylinder internally heated oil bath by Chromalox electric heating rods, 126" face Nomex Blanket, controls.

d. DSI A-Frame Winder, Direct Coupling to spline shaft, 7.5-HP

INSPECTION DEPARTMENT

1

No. 2 Inspection Machine, Menzel with 110" non-driven Cradle let-off, top pull roll driven 3/4-HP, Viewing Board with OH Light, 126" face with ydg. Clock, operator platform and controls, 2-Roll Surface Winder 126" x 9" Bed Rolls, Edge Guiding, and Dump-to-Conveyor

1

No. 3 Inspection Machine, Menzel with 126" non-driven Cradle Let-off, Viewing Board 134" wide with Thru-light and OH Light, Birch Auto Measure 3000 Yardage Counter, op. platform, and 2-Roll Winder 126" x 10" Bed Rolls, Edge Guiding, and Dump-to-Conveyor.

1

No. 5 Inspection Machine, Birch Brothers, with Roll-Table 76" x 96" wide, 2-Roll Un-Wind with 130" x 10" Bed rolls, Lighted Viewing Baord 136" wide, Birch Auto Measure 3000 Yardage Counter, Op. Platform and Controls, Fife Guiding, 2-roll Winder with 130" x 10" Bed Rolls.

1

Double & Roll Machine, consiting of;

a. Intra 195" face Let-off with Core holder, 195 x 10" Bed Rolls,, Intra CUWSL40-1991, S/N 91-289,

b. Intra Inspection Machine with lighted viewing board and lighted vewing section, yardage counter, OH light.

c. 2-Roll Intra Winder with Edge Guiding, 138" face x 10" Bed Rolls

d. Folding Apex overhead with Guider Specialty Air Guiders for edge control.

e. TMI-Cooper 2-Roll Winder with 72" x 10" Bed Rolls with Edge Guiding.

1

Van Vlaanderen type Inspection Machine 134" face width with single-arbor let-off and Jack stand, solid viewing board, TruMeter yardage counter, center wind take up with seconds rewind, 480 volts.

PALLET RACK STORAGE

Finished Goods Warehouse:

8

48" x 22' x 101" wide, 3-tiers high, Med. Duty, Teardrop

12

48" x 22' x 10' wide, 6-tiers high, Med. Duty, Teardrop

10

48" x 22' x 10' wide, 6-tiers high, Med. Duty, Teardrop

10

48" x 22'  x 10' wide, 6-tiers high, Med. Duty, Teardrop

40

Total